back to set up page
Under construction:

Speeding fines doubled in this area.
Your solution was
processing for 10
hours. You have let it
stand for 12 to 24
more hours.

Remove the two wires
and clean them gently,
store them until you
are ready to make the
next batch.

Take the jar and stir
the solution very
gently with a spoon or
preferred glass stirring
rod.

You will notice a lot of
grayish to almost black
feathery substance in
the bottom of the jar.

This is normal and
must be filtered out. It
consist of larger Silver
particles, and O2
reactive or oxidized
silver.
10 hours of processing, 12 to 24 hours of sitting and now your Ionic Silver Solution is ready
for filtering.
Make sure you clean
off the wires. Just wipe
them down with a
napkin or paper towel.

Place the wires in a
safe place. Wrapped in
a paper towel or
napkin.

Store in a dry place
until needed for the
next generation time.

These wires will make
3 to 5 gallons of
solution, possibly more.
The next thing we need to do is filter the solution. I am using laboratory glass wear in the demonstration.

You can use any clean, and I mean clean glassware you have.

Take a drinking glass of about 8 oz volume, place the filter on the top, fold paper over the glass edge, and
you have a great filter set up.

Below is a picture of the items you will need. Feel free to substitute your own glass wear items if you do
not have laboratory glassware.
Filter paper, # 2 cone
coffee filter is shown
here. Any good quality
coffee filter will do.

Blue (Cobalt Blue Color)
glass bottles for final
packaging and storage
of Ionic Silver Solution.

A funnel or filter holder.
If you do not have a
funnel, place the filter
into a round 8.oz
drinking glass, fold the
paper around the top
edge and use the glass
as a holder.

MAKE SURE THE          
GLASS WEAR IS           
 CLEAN, CLEAN,   
   CLEAN.
Pour some of the
solution from the large
generation jar into a
smaller more
manageable container.
I am using a 500 ml.,
beaker.

You may notice a slight
tint to the water.
Somewhere between a
dull yellow to a
brownish.
Sit up the filter, and
gently pour the solution
from the jar into the
filter.

If you get any liquid
into the receiving glass
that  is not filtered. Do
It Again.

YOUR FINAL    
SOLUTION MUST BE
FILTERED.

SOME LIKE TO
FILTER THE
SOLUTION TWO
    TIMES.
Now pour the Filtered
Ionic Solution into your
storage bottle. I do
prefer the Cobalt Blue
Glass.

I have not seen any
Silver plating on the
Blue bottles even after
a year of storage.

Other colors and
bottles types show
Silver plating the inside
after only a few months
storage.

If the Silver plates the
bottle sides you loose
ppm value in the
solution.
Bottle your Ionic Silver
solution.

Fill the bottles up until
they run over some.

Place cap on bottle and
secure.

Wipe outside of bottles
down with a paper
towel.

Store in a dark quiet
place.

Ionic Solution in the
Dark Blue bottles have
been in storage for
over a year in my
testing. They have not
lost any of the ppm to
plating on the glass.
Pour into bottles, wipe them dry and store in a dark quite place.
Pouring filtered solution into final
packaging
Filtering Solution
That is the process. With care and some patience you can create up to a gallon of Ionic Silver for your own personal
use.

Using this as a guide line the ppm per volume will be at 10 to 15 ppm Ionic Silver. Water temperature is the deciding
factor on how much ppm per volume is created. I assume a room temperature of 69 to 72 degrees for this
demonstration.


Take the generation jar you made the Silver solution in and do not wash it. Rinse it out with distilled water several times
and then store it upside down until needed again.
Below are some pictures with a Red
and a Green laser beam going through
the Ionic Solution.

You can see the suspension of Silver
in the water.
If you choose to make your own Ionic Silver Solution you must use clean glass. Pure distilled water. Pure Silver.

Cutting corners, taking short cuts, using contaminated glass can and will result in compounds that are very dangerous
to you.

You take all responsibility upon yourself if you choose to make Ionic Silver.

I created this so those who want to try to make the Ionic Silver Solution. For those who would like to try the
solution. To be able to do so with out spending huge amounts of money or resources.

There is no need to spend hundreds of dollars a gallon for a solution, when you can make it better and
probably purer than what you may purchase.

Remember:

A little Ionic Silver goes a long way.

Haste makes waste:

Do not cut corners or try to accelerate the process.
Caution


Keep in mind that Ionic Silver is a very potent ingredient.
Do not over use the product.

Use the product with respect as to what it can accomplish and to what it can not do.

AS with any potent medical material, you are responsible for the use and application of the product.

The material listed on these pages for the formulation and creation of Ionic Silver.

This site was put up so that those who attempt to create Ionic Silver for their own use. Could find some directions
on how to make the solution in a safe, efficient, and quality controlled environment.

Avoid contamination. Do not use old glass wear, old food jars such as pickle jars. Those jars had acid based
ingredients and the acid may have dissolved other metals and place them into the glass.
That will contaminate your end product.

Use new jars.
ONLY HIGH QUALITY, PURE SILVER FOR YOUR PROJECT.       
USE ONLY DISTILLED WATER.
DO NOT USE SPRING WATER, FILTERED OR TAP.
USE ONLY DISTILLED WATER.
READ CAUTION AT  BOTTOM OF
PAGE BEFORE STARTING.
READ CAUTION AT BOTTOM OF
PAGE BEFORE STARTING